Ghost Controls Hinge & Roller Replacement Nationwide

Ghost Controls Hinge & Roller Replacement: The West Palm Beach Owner's Guide

We stock and install Ghost Controls-compatible hinge and roller replacements for most residential swing and slide gate models, with typical installed pricing in West Palm Beach running between $165 and $380 per hinge or roller assembly depending on the series and how much hardware has worn around it. Most calls come in after a gate starts dragging, squealing, or sagging toward the latch post. We carry OEM-spec Ghost Controls parts and quality aftermarket equivalents on the truck, so most replacements are done on the first visit.

Call (728) 203-0817

If your gate still opens and closes but sounds rough, feels heavy, or doesn't seat flush against the stop, you're probably describing a hinge or roller that's given up its bearings or worn past adjustment. Tell me what it's doing and what it stopped doing – that's usually enough to get started. Once we hear the symptom, we can typically match the part to your model before we arrive.

Which Ghost Controls Models This Applies To

Ghost Controls builds both swing-arm and slide gate openers, and their hinge and roller hardware spans three main families: the residential swing gate kits (AXDP and AXD series), the heavier-duty dual swing kits (TSS1 and TDS2), and the slide gate kits (SLY and SLD series). The hinge and roller part numbers differ by gate weight and post configuration, so we always ask for the model plate info from the operator arm itself or the original installation manual if you kept it.

One compatibility gotcha we see in West Palm Beach often: Ghost Controls' earlier-generation AXDP swing kits used a fixed-pin hinge with a nylon wear bushing, while their newer AXDP versions switched to a sealed ball-bearing hinge. They look almost identical on the post, but swapping the old for the new without checking the pin diameter and post bracket bolt spacing will leave you shimming something that should fit clean. We measure the pin, the bracket spread, and the gate's actual weight before we quote. When we can match the spec exactly with a quality aftermarket part, we tell you and let you choose. When the OEM part is the only good option, we say that too – no vague "comparable quality" language.

Signs Your Ghost Controls Hinge & Roller Replacement Is Failing

• Gate sags toward the latch post by more than half an inch. The hinge pin bore has wallowed out or the roller axle has worn oval, and the gate's weight is now resting on the operator arm instead of the hardware.
• Metal-on-metal squeal or a heavy grinding sound when the gate moves. The bearing or bushing inside the hinge or roller has failed, and the pin is riding directly against the housing. In coastal air, this gets worse faster because the salt works into the exposed surfaces.
• Gate stalls mid-cycle and the operator throws a force error. A tired roller adds drag the opener wasn't designed for, and the Ghost Controls board reads that as an obstruction.
• Visible rust staining around the hinge leaf or roller bracket. South Florida humidity penetrates paint chips and surface wear, and once the bearing seals fail, the rust moves inside the assembly.
• Gate wiggles side to side by hand when closed. The bottom roller or load-bearing hinge has too much play, and the gate's resting position shifts every few days.

Replacement Cost & What's Included

For most Ghost Controls residential swing gates in West Palm Beach, hinge replacement runs $165 to $270 per hinge installed, including the part, removal of the old hardware, and realignment. Roller replacement for slide gates typically lands between $220 and $380 per roller assembly, with the higher end covering trucks with sealed stainless bearings and heavier gates that need the track dressed at the same time. If both hinges need doing, we quote a pair price that's better than doubling the single rate.

Every quote is a written price delivered before we touch a tool. You'll see the part cost, the labor, and the exact total – and we won't start until you approve it. Every hinge and roller replacement carries the 365-Day Done Right Promise: if it isn't right, we make it right. No argument, no fine print. We also lay drop cloths under the work area and put on shoe covers before stepping inside any gate or garage space, and we take a cleanup photo before we leave.

DIY or Call Us?

Two things are safe to check on your own: whether the hinge bolts are backing out (the gate will rock when you push it), and whether the roll pins or bearings are visibly rusted. Tightening loose bolts is fine. Beyond that, this is one of those repairs where experience matters more than a YouTube tutorial, because a Ghost Controls gate under spring or opener tension can shift suddenly when you pull the hardware, and a gate that's hanging wrong can drop on hands, kids, or pets.

We've also seen owners replace a hinge with a close-enough part, only to cook a Ghost Controls operator six months later because the gate's throw geometry changed by half an inch. The operator doesn't recalibrate itself for that. If you want a laser-level alignment, the right spec part, and a warranty that covers the whole job, call (728) 203-0817 and we'll get it sorted. Live person answers, every time.

FAQs