Ghost Controls Gate Installation Nationwide

Ghost Controls Gate Installation in West Palm Beach: What to Know First

Ghost Controls gate installation in West Palm Beach runs $450 to $2,800 depending on whether it’s a single swing arm, a dual-leaf driveway setup, or a full sliding gate with safety edges and a battery backup. Most installs take one day, sometimes two when we’re running conduit under an existing paver driveway or tying into an older keypad that wasn’t wired for a modern control board. You get a written price before any work starts, and we don’t charge extra for the things homeowners actually notice: shoe covers, drop cloths, and a cleanup photo before we pull out of the driveway.

Call (728) 203-0817

This page is for West Palm Beach homeowners who already own Ghost Controls equipment, or who are comparing it against LiftMaster and Mighty Mule, and want a straight answer about installation. Latch and Post Gate Repair West Palm Beach is an independent Ghost Controls service provider, not a factory-authorized installer. That matters less than you’d think: we’ve been putting these systems in since 2009, and we know what fails on them in South Florida salt air. Call (728) 203-0817 if you’d rather talk through it than read about it.

How Ghost Controls Products Fail – and How We Fix Them

• AXV series arm binding on unlevel posts. The AXV single-arm operator is a workhorse, but it doesn’t forgive a post that’s even three degrees out of plumb. When the arm flexes against a leaning post, the internal limit gears wear twice as fast, and we get called out for a gate that stops 18 inches short of closed. On install, we shim and brace the post before mounting the arm, not after. It adds 40 minutes and saves a $180 control board later.
• AXDP dual-gate desync after power flickers. West Palm Beach gets frequent brownouts during afternoon thunderstorm season, and dual-swing Ghost Controls setups are sensitive to them. When the two boards lose communication mid-cycle, one leaf closes and the other stays open, and the remotes stop pairing until someone re-learns them. We install a surge-protected outlet on every dual install and set the sync delay to match the heavier leaf’s travel time, which keeps both arms moving like they’re one unit.
• Wireless keypad battery drain in coastal humidity. The Ghost Controls wireless keypad model WKP1 eats 9-volt batteries in six to eight weeks along the Intracoastal corridor, because the seal around the weather gasket swells in the salt humidity and the board wakes up constantly. We re-gasket the housing with a marine-grade seal on installs within three miles of the water, which is a detail you won’t find in the manual.
• Armature bolts shearing on the TSS1 solar model. The TSS1 solar kit’s armature mounting bolts are standard zinc, and between the salt air and the vibration of a driveway gate cycling 20 times a day, they corrode and seize. We replace them before failure with stainless bolts on any install where the gate opens more than 10 times daily, and we torque them to spec instead of guessing.
• Photocell eyes misaligned by lawn equipment. This is a Ghost Controls install reality more than a manufacturing defect: the safety photo eyes mount low, and a string trimmer or a kid’s bike clips one, and suddenly the gate refuses to close. We mount them at 24 inches on pipe-thread brackets with a tamper-resistant locknut on West Palm Beach installs, because we’ve seen too many neighborhoods where lawn crews work every Tuesday and the gate goes down every Tuesday night.

Our Ghost Controls Gate Installation Process

Every install follows the same sequence, because Cody Beckman has learned over fifteen years that skipping step two always costs you step five.

1. 1
   Tell me what it’s doing and what it stopped doing. We start with a phone conversation about the gate’s behavior, the age of the Ghost Controls operator, and whether the problem started suddenly or crept in. That usually tells us which parts to bring before we ever see the driveway.
2. 2
   On-site measurement and post inspection. We check post depth, gate weight, hinge condition, and the exact Ghost Controls model on the gate. If the post is shifting or the gate sags, we address that before anything electric goes in.
3. 3
   Written price and parts decision. We give you the number in writing before touching a single bolt. We discuss OEM versus quality aftermarket parts where it matters, and we default to Ghost Controls OEM boards and arms when the unit is under warranty.
4. 4
   Installation and wiring. We mount the operator, run the conduit, set the limits, pair the remotes and keypad, and wire the safety edges. On dual-leaf systems, we time the sync so both arms open and close as one.
5. 5
   Test to failure. We cycle the gate 25 times, block the safety beam, and force an obstruction event. If the gate hesitates, we don’t close out the ticket. We find the issue before you ever see it.
6. 6
   Cleanup and cleanup photo. We clear the work area, put tools back in the truck, and send you a photo showing the finished install and the clean driveway before we leave.

What Ghost Controls Gate Installation Costs in West Palm Beach

Ghost Controls systems are the most common gate operators we install in West Palm Beach, and the working range on a typical install looks like this:

• Single swing gate, AXV arm, one remote: $450 to $800
• Single swing gate, AXV arm, keypad, two remotes, battery backup: $750 to $1,100
• Dual swing gate, two AXDP arms, keypad, safety edges, two remotes: $1,300 to $1,900
• Sliding gate, Ghost Controls sliding operator, safety edges, photocells: $1,600 to $2,800

What moves the price in West Palm Beach is driveway width, gate weight, and how far the nearest outlet is from the gate. A 16-foot double-leaf gate with a brick column on one side and no power within 40 feet will always cost more than a lightweight aluminum single on a concrete pad. You’ll see the exact number in writing before we start, and the number you approve is the number you pay. Call (728) 203-0817 for a free estimate on your specific setup.

Why West Palm Beach Homeowners Call Latch and Post Gate Repair West Palm Beach for Ghost Controls Work

We’re the people you call on a Tuesday morning when the gate stopped at 11:40 last night and the dog is looking at you like you’re supposed to fix it. Every job we do is backed by the 365-Day Done Right Promise: if the installation isn’t right, we make it right, no argument and no fine print. Our technicians are factory-trained on Ghost Controls equipment and also on LiftMaster, Mighty Mule, and DoorKing, which matters when we find a mismatched receiver or an old keypad that won’t pair with a new Ghost Controls board. We’re part of the Cedarwell family, independently owned and operated since 2009, and we work to the Cedarwell C.A.R.E. values on every visit: Clean up like it’s our own home, Ask before we move or touch anything, Respect the family’s time and quiet hours, Explain the price before the work. We lay drop cloths on your floors and put shoe covers on before stepping inside, and we can schedule around nap time if quiet matters.

FAQs