Ghost Controls Gate Repair Nationwide

Ghost Controls Gate Repair in West Palm Beach: What to Know First

Ghost Controls gate repair in West Palm Beach typically costs between $185 and $480 for most common failures, and our technicians usually complete the diagnosis and fix in a single visit. As an independent Ghost Controls service provider, we work on the full line including the RTE, AXDP, and TSS1 series openers, plus the hinges, arms, and control boards that wear out alongside them. If you’re a homeowner whose Ghost Controls gate has stopped opening, started beeping, or reversed mid-cycle, this page will tell you exactly what’s happening and what it costs to make it right. Call (728) 203-0817 and a live person will answer, day or night.

Call (728) 203-0817

How Ghost Controls Products Fail – and How We Fix Them

• The opener clicks but the gate won’t move – RTE and TSS1 series. This is the failure we see most often in West Palm Beach’s humidity, and it’s rarely the motor itself. The culprit is almost always a control board that has absorbed moisture through the case seams, corroding the relay contacts. Our fix is a board replacement with the OEM part when it’s still available, or a sealed aftermarket board with conformal coating when it isn’t. Your gate moves again without a full opener swap.
• The gate opens but stops halfway and reverses – AXDP and TSS1 series. Ghost Controls uses a potentiometer and limit pin system to tell the opener where the travel ends are. When a pin bends, which happens over time as the gate sags or a kid swings on it, the opener loses its reference point and assumes something is in the way. The fix is a limit pin replacement and gate realignment, not a new motor. We did one of these last month in a neighborhood off Parker Avenue, and the whole repair took forty minutes.
• “Ghost beeping” – the opener chirps and beeps in the middle of the night for no visible reason. This is almost always a failing battery in the unit’s internal power supply. Ghost Controls boards use a small rechargeable cell to hold settings during outages, and once that cell swells, voltage drifts and sets off false alarms. Replacing the cell is a $35 part and about an hour of labor. We recommend addressing it before it damages the board permanently.
• The gate slams or drifts after releasing – RTE series. Ghost Controls openers are not meant to hold the gate closed on their own; they rely on your gate’s mechanical stops and latch. Over time, the close stop rubber wears down and the gate starts drifting past it, which tells the opener to over-correct. New stop bumpers and a latch adjustment solve this completely.
• Remote works from ten feet away but not from the street – all Ghost Controls series. The antenna on Ghost Controls receivers is a short wire tucked inside the control box. In West Palm Beach, aluminum gate frames and dense landscaping with palm fronds degrade the signal. We relocate the antenna outside the box, add a small extension, and range comes back without buying a new remote or receiver.

Our Ghost Controls Gate Repair Process

1. 1
   You call and talk to a live person. No menu tree, no callback. We ask the question Cody Beckman always asks first: “Tell me what it’s doing and what it stopped doing – that’s usually enough to get started.”
2. 2
   We arrive and diagnose without touching anything first. Our technician walks the gate, listens, checks the board for visible corrosion or pin damage, and opens the control box only after explaining to you what they’re looking at.
3. 3
   We give you a written price before any work begins. You’ll see the exact part cost and labor figure in writing while the gate is still open. No pressure, no hidden fees, and the price we write is the price you’ll pay.
4. 4
   We make the repair with OEM Ghost Controls parts whenever they’re available. When a factory part is discontinued, which happens on older RTE units, we use an equivalent aftermarket part and tell you exactly what we’re putting in and why.
5. 5
   We test the full cycle in front of you. Open, close, obstacle detection, remote range, and battery function all get checked before we call it done.
6. 6
   We clean up and show you a photo. Shoe covers on, drop cloths down, tools packed, and a picture of the clean area before we leave.

What Ghost Controls Gate Repair Costs in West Palm Beach

The biggest variable is your specific Ghost Controls model and how accessible the control box is. A board replacement on an RTE takes under an hour; on an AXDP with a buried conduit it can take half a day. You’ll always see the exact number in writing before we start. Call (728) 203-0817 for a free estimate over the phone or at your gate.

Why West Palm Beach Homeowners Call Latch and Post Gate Repair West Palm Beach for Ghost Controls Work

We’re a Cedarwell-family gate specialist, and we’ve been serving South Florida since 2009. Our technicians are trained on Ghost Controls specifically, not just generically on gate openers, and they understand the salt air and humidity problems that hit equipment in West Palm Beach differently than it wears elsewhere. Every repair is backed by the 365-Day Done Right Promise: if it isn’t right, we make it right, no fine print. And if the diagnosis shows a non-Ghost Controls component is the real problem – perhaps a Viking Access operator hiding behind an old Ghost Controls arm – we service that too, along with LiftMaster, Mighty Mule, and DoorKing, so a mixed-brand gate never needs two service calls. Every visit includes shoe covers, drop cloths where our work takes us inside, and a cleanup photo before we leave. We treat your gate and your home the way we treat our own.

FAQs