FAAC Hinge & Roller Replacement Nationwide

FAAC Hinge & Roller Replacement: The West Palm Beach Owner’s Guide

We stock and install FAAC-compatible hinge and roller replacement parts across West Palm Beach, with most swaps running $180 to $420 installed depending on your gate’s weight and which series you own. We carry the common wear items on the truck, so we can usually complete the job the same day we diagnose it, and you’ll see the full written price before we touch a single bolt. The way most owners find out a hinge or roller has failed is simple: the gate starts dragging, scraping, or leaning just enough that it no longer closes square against the post.

Call (728) 203-0817

In West Palm Beach’s salt air and afternoon storms, FAAC hinge pins and roller bearings wear faster than the operator does. The motor keeps working fine while the hardware underneath quietly loses its tolerance, and one day the gate hangs low enough to catch the driveway. That’s the part we’re replacing, and it’s a straightforward job when it’s caught before the gate drops onto the pavement.

Which FAAC Models This Applies To

FAAC builds swing gate systems under several series names, and the hinge and roller hardware varies between them. The most common models we service in West Palm Beach are the FAAC 390, 391, 412, 415, and 770 series for residential swing gates, along with the heavier 844 and S700H lines for larger properties. If your gate swings on FAAC hinges, the pivot point is either a bearing-loaded hinge block or a reinforced steel leaf hinge, and the roller at the bottom keeps the gate riding level as it opens. Rollers on the 415 and 770 series tend to be delrin or nylon wheels on a sealed bearing; the 390 and 391 use a simpler steel roller that rusts faster near the coast.

To match the right part, we look for the FAAC part number stamped on the hinge body or on a small metal tag near the bottom pivot. If the stamp is gone, we measure the hinge leaf, pin diameter, and bolt spacing, then cross-reference against the gate’s weight and frame material. FAAC’s OEM hardware is well made, but for steel gates that sit close to salt spray, a quality aftermarket stainless-steel hinge often outlasts the original zinc-plated part. We’ll show you both options and quote each one in writing, since independent gate shops like us are not affiliated with FAAC and can choose freely what goes on your gate.

Signs Your FAAC Hinge & Roller Replacement Is Failing

• The gate scrapes the driveway on the latch side. When a bottom hinge or roller wears, the gate loses a quarter-inch of clearance and the far end drags. You’ll see bright metal or a half-moon scratch on the concrete where the gate bottom contacts it.
• The gate leans toward the post. A worn top hinge pin lets the whole leaf tilt inward, so the latch no longer lines up with the receiver. The operator pushes harder to compensate, which shortens its life.
• You hear a rhythmic squeak or grind while the gate moves. That’s the roller bearing running dry and the metal race wearing into the wheel. Once the bearing separates, the wheel stops turning and the gate drags the roller across the track or driveway.
• The gate shudders when it stops. Worn hinge bushings create play, so the gate doesn’t stop cleanly – it rocks back and forth for a second or two. On a heavy FAAC 770 gate, that rocking puts stress on the operator’s gearbox.
• The gate opens fine in the morning but binds in the afternoon. Florida heat expands a steel gate slightly, and a marginal hinge or roller shows it first. The metal grows, the clearance disappears, and the gate sticks until it cools.

Replacement Cost & What’s Included

For West Palm Beach homes, a single FAAC hinge or roller replacement typically lands between $180 and $420 installed. The range comes down to three things: whether you need one hinge or a set, whether your gate needs stainless-steel hardware for salt exposure, and whether the roller track or mounting bolts also need attention. A lightweight single-leaf gate on a 390 series might run closer to $180; a heavy 770 series with two worn hinges and a steel roller can push toward the top of that range.

Every quote we give includes the part, the labor, and the adjustment of the gate so it closes square and true. We write the price down before we start, and the number you see is the number you pay. No discovery fees, no “while we’re here” add-ons. And because we stand behind our work with the 365-Day Done Right Promise, if the hinge or roller isn’t right a year from now, we make it right.

DIY or Call Us?

Some things on a FAAC gate are safe to check yourself: visible rust on the hinge body, a wheel that’s not spinning, a bolt that’s backed out half a turn. You can photograph those and send them to us, and we’ll tell you what we think before we ever come out. What you shouldn’t do is unbolt a load-bearing hinge on a 300- to 800-pound swing gate. The moment that hinge comes free, the gate wants to drop, and a swinging leaf that size can do real damage to a person or a car. That’s the part where a trained technician with a jack stand and a second set of hands is worth the call.

If you’re in West Palm Beach and your FAAC gate is dragging, leaning, or squealing, call us at (728) 203-0817. We’ll get you a straight answer on what it needs and what it costs, and we’ll only touch the gate after you’ve seen the written price. Shoe covers on, drop cloths down, photo of the clean-up before we leave.

How long do FAAC hinges and rollers last in Florida?

In West Palm Beach, you’ll typically get 5 to 8 years out of a zinc-plated FAAC hinge or steel roller before the salt air and rain start winning. Stainless-steel hardware can double that on most residential gates.

Can a worn FAAC hinge be repaired instead of replaced?

If the hinge body is intact and only the pin or bushing is worn, we can sometimes press in a new pin and bushing for less than a full hinge replacement. If the hinge leaf itself is cracked or the bolt holes have wallowed out, the hinge needs to be replaced.

How long does a hinge or roller swap take?

A single hinge or roller on a FAAC swing gate usually takes 45 to 90 minutes once the gate is safely supported. Replacing a full set of hinges plus a roller on a heavy gate can run two to three hours including adjustment and testing.

Do you stock FAAC hinge and roller parts on the truck?

Yes. We carry common FAAC hinge pins, bushings, and rollers for the 390, 391, 412, 415, and 770 series, along with compatible stainless-steel upgrades. If your gate needs a part we don’t have on the truck, we’ll get a written price and a timeline before we leave your driveway.

Written by Cody Beckman, Owner, Latch and Post Gate Repair West Palm Beach at Latch and Post Gate Repair West Palm Beach, serving West Palm Beach and nearby areas.